GIOVANETTI GOLF
Giovanetti Golf
Home The Lineup The Fitting On-Course Analysis About
Instagram · X / Twitter
studio@giovanettigolf.com
σ
Giovanetti Golf · The Lineup

The Lineup

Three head designs. Six configurations. Infinite specifications. Every head is engineered to spec, and built to yours.

The Models
01MODEL
01 OF 03

G05 BLADE

The foundational blade. Compact, low-profile, direct.

MATERIAL303SS
HEAD TYPEBLADE
CONFIGSG05P / G05F
G05P · Plumber's · 30° TH · Moderate Feedback G05F · Flow · 45° TH · Higher Feedback
  • Built for the consistent stroke
  • Neck height, thickness, lateral & forward offset, all mechanically optimized
  • Tuned for superior sound and feel
  • Most face awareness in the lineup
G05 design render, isometric view G05 design render, view at address G05 design render, sole view from below
Drag to rotate
G05P · DESIGN RENDER303 STAINLESS STEEL
02MODEL
02 OF 03

G32 MID-MALLET

The engineered mid-mallet. More stability than the blade, without the bulk of a full mallet.

MATERIAL303SS
HEAD TYPEMID-MALLET
CONFIGSG32P / G32F
G32P · Plumber's · 30° TH · Moderate Feedback G32F · Flow · 45° TH · Higher Feedback
  • Deeper, heavier body than the G05, with more rearward mass
  • Larger MOI envelope: less face rotation on off-center strikes
  • More internal volume lowers the resonant frequency at impact
  • Lower, more muted response, tuned for soft feel
G32 design render, isometric view G32 design render, view at address G32 design render, sole view from below
Drag to rotate
G32P · DESIGN RENDER303 STAINLESS STEEL
03MODEL
03 OF 03

G33 MALLET

The flagship mallet. Highest MOI and deepest CG in the lineup.

MATERIAL303SS
HEAD TYPEMALLET
CONFIGSG33P / G33F
G33P · Plumber's · 10° TH · Near Face-Balanced G33F · Flow · 35° TH · Moderate Feedback
  • Most stable head in the lineup
  • Least face rotation on off-center strikes
  • Forward roll initiated sooner off the face
  • Largest footprint, built to aim and hold its line
G33 design render, isometric view G33 design render, view at address G33 design render, sole view from below
Drag to rotate
G33P · DESIGN RENDER303 STAINLESS STEEL
The Hallmarks

Two design decisions that define every Giovanetti putter.

◎

CG-ALIGNED SIGHTING

Every putter carries a sight dot and sight line. Align it at address and you place the CG, not the geometric face center, on your start line. No two of the six configurations share the same sight line. This is intentional.

Δ

STRUCTURAL GUSSETS

The most critical load-path and mass-distributing feature of every head. They stiffen the junction, cut micro-deflection at impact, and keep energy transfer consistent across the face. MOI is directly reliant on the gussets.

G05P on the green, flag on the target line
G05P · PROTO 1 · ON COURSEORLANDO, FL
The Physics

Why mass distribution is the most important decision in putter design.

CG

CENTER OF GRAVITY

The single point through which the head's weight acts. CG controls loft sensitivity at impact, forward roll, and feel at contact. Tuned and verified against design intent in every putter.

MOI

MOMENT OF INERTIA

A head's resistance to twist on off-center contact. Higher MOI, less face rotation on mishits, more consistent direction. Tuned to each model's stroke profile, not maximized arbitrarily.

θ

TOE HANG

Toe hang does not dictate stroke path. It communicates face orientation. The lineup spans 10° to 45° across six configurations, covering nearly every real stroke profile.

SPECIFIC DESIGN PARAMETERS, GEOMETRY VALUES, AND MASS DISTRIBUTION DATA ARE NOT PUBLISHED HERE.

G05P face on, studio
G05P · PROTO 1303 STAINLESS STEEL
NDES Architecture

Nothing Decorative. Everything Structural.

No geometry exists for looks alone. Every feature, every gusset, every mass pocket is placed because the physics demand it. The result looks exactly like what it is. Focused, engineered hardware.

You are not getting a putter that was styled first.
You are getting a putter that was solved first.

G05P profile, studio
G05P · PROTO 1303 STAINLESS STEEL
MATERIAL

303 Stainless Steel

303SS is the gold standard for Giovanetti putters. Selected for feel, density, and machinability. Never compromised for cost. Performance over everything.

MANUFACTURING

CNC Milled

Machined on a 5-axis CNC mill from solid 303 stainless steel billet. CG, toe hang, and mass distribution calculated and tuned before a single cut is made.

ASSEMBLY

By the Engineer Who Designed It

Every putter is assembled by the same person who designed the head and performed the structural analysis. No production line, no technician, no fulfillment center. Adjusted to your lie, cut to your length, finished to your grip, by the engineer whose last name is on it.

The Next Step

One putter. The rest of your life.

The right putter starts with the right conversation.

Prototype access. Launch priority.

Limited Production. First List, First Access.

Prototype access. Launch priority.

YOUR HANDICAP
σ YOU'RE IN. We'll be in touch when it's time.
JOIN THE LIST
GIOVANETTI GOLF
Instagram · X / Twitter
Get in touch · studio@giovanettigolf.com σ

LAKE NONA, FL · NOTHING DECORATIVE. EVERYTHING STRUCTURAL.
© 2026 GIOVANETTI GOLF LLC. ALL RIGHTS RESERVED.
PRIVACY · TERMS

0